How To Install a Saddle Valve for Your Humidifier or Refrigerator

Last update in February, 2023

This time of yr in the Midwest deliver lots of modifications to our life. Altering the Clocks implies leaving and returning home in the darkish. A further alter is the indoor air good quality in our houses. The chilly dry air of wintertime reminds us it is time to turn on the Humidifier.

I just received a contact from a relative who just turned on the drinking water supply to the Humidifier and it was now leaking. Soon after a few issues, followed by a recommendation the dilemma was remedied in a couple minutes. This telephone contact acquired me to pondering about those troublesome saddle valves that supply h2o to so several humidifiers and ice Makers.

Safety very first, Under no circumstances Ever use a saddle valve for any form of gas, only water. A saddle valve will get its identify from the way it appears, like a saddle on a horse. They are an low-cost way to get drinking water to humidifiers, ice Makers, and many others. There are quite a few a bit various versions but all have the same parts and are set up the exact same.

You will be performing on a are living water pipe so prior to you commence track down the water shutoff in your house, just in case you need to have to quickly turn the drinking water off.

Take a appear at the photo beneath and cautiously glance at the elements of the valve I have labeled. The saddle is the part that wraps close to the pipe, and is held with each other by 2 screws or bolts. The Seat of the valve is in which the needle valve (or stem valve) travels through and punctures the pipe. In between the Seat and the pipe is a rubber gasket that seals the location close to the needle valve puncture. The needle valve works effectively on copper and plastic pipe, but not incredibly very well on galvanized pipe.

The first step to install the valve is to clean the pipe all the way close to in which the valve is heading to be installed, generally with a mild sanding. Up coming place the valve about the pipe, with the output relationship and top of the needle valve in a situation that you can effortlessly obtain each. Consider into thought where by the output line has to operate to. When positioning the saddle valve all around the pipe be careful to make sure the gasket is seated effectively. Just one trick is to screw the needle valve down right until it barely touches the pipe, permitting you to properly middle the gasket. When you have the gasket effectively seated tighten the saddle valve, evenly, alternate with a pair turns on every side until eventually very good and cosy.

Next connect the output line to the saddle valve, leaving a lot of more length and location the conclusion in a bucket or ground drain. You are now prepared to transform on the water. Slowly but surely convert the needle valve so it pierces the pipe. When you are not able to turn it by hand anymore slowly back again twist it backwards. Drinking water should now start to occur out of the finish of the output pipe. If not then repeat turning it in to pierce the pipe.

At the time you see h2o coming out the output pipe close the valve and connect the output line to your Humidifier, Ice Maker, and many others. now turn it on a single last time, checking for leaks.

If it does leak from the needle valve stem, then you wants to pretty slowly and gradually tighten the nut (packing nut) that surrounds the needle valve (refer to picture). If it leaks from the gasket space, look at to make confident the screws holding the saddle valve to the pipe are tight.

A widespread exercise is to flip the saddle valve off when you convert off the Humidifier in the spring. If you do this, it is most likely in the tumble when you transform it back again on it will leak from the needle valve stem. Not to fear, just transform the packing nut slightly right until the leaking stops.

If you need to have to ever exchange the whole valve, transform the h2o off and open the faucets of a Sink at a reduce level to drain water from the pipes. Take away the saddle valve and just take it to the shop with you to make sure you acquire a new one with the identical dimension needle valve. Comply with the higher than methods to set up the new saddle valve with one additional move. When you fit the saddle valve to the pipe, lining up the gasket and needle valve will be future to unattainable except you increase the needle valve, then implement the gasket and insert the protruding needle valve into the current hole. Then go on following the steps as outlined previously mentioned.

Stick to the previously mentioned ways and you will have a successful set up of a saddle valve.

Trustpilot